Kingwood Underground
the heart and soul of our Kingwood, Texas family
Login - Create Account - Help
Clean out your garage on Kingwood bookoo! Or find local garage sales on Yard Sale Search.com
KU Live!

Have you ever replaced the wood slats in a porch bench?

who's talking here?

Gigix4 1
Tipsyhic 1
Steveneedsbeer 1
Mabs 2
Dorothy Parker 2

     » send to friend     » save in my favorites     » flag dangerous topic flag as a dangerous topic

Dorothy Parker --- 15 years ago -

If so, where did you get the lumber and how easy was it?

We have a nice one, but it's horribly weathered and needs to be repaired.

Thanks in advance! 

Mabs --- 15 years ago -

Most slats are 4 feet long by 2.75 inches wide by 3/4 thick,( unless you have a 5 foot bench, in which case they would be 5 feet long), Home Depot or your local lumber yard would have these...at some places they could cut them for you. All you might have to do fancy would be to round off the front edge of the slat that goes at the front of the seat.

How to Replace the Wooden Slats in Garden Benches
By Kenneth Crawford, eHow Contributor
Garden benches are an attractive addition to your yard or garden, but over time weather will take its toll on the wooden slats of the bench. When this happens, the only way to restore functionality and an attractive appearance to the bench is to replace the slats. This is best done in stages. The slats not only provide seating, but they also hold the two sides of the garden bench together. If you leave the end slats on the bench while you replace the others, the sides will remain stable and the entire job will be easier.

Difficulty: Moderately Easy
Instructions
things you'll need:

Tape measure
Wood slats
Bolts, 1/4-inch, 4 inches long, with nuts
Vise grips
Flathead screwdriver
Pencil
Coping saw
Drill with 1/4-inch bit
Stain
Paint brush
Preparation and Removal
1
Measure the length of the garden bench slats and the width of each with a tape measure. Count the number of slats requiring replacement. Go to a home-improvement center and purchase wood strips of oak, cherry or pine in the width necessary. The pine wood is a softer wood and is not suitable for benches more than 3 feet long.
2
Purchase 4-inch-long, 1/4-inch bolts with nuts for attaching the new slats. When purchasing the bolts, select ones with a an oval head for use with a flat-head screwdriver. Select a stain of your choice for the new slats.
3
Remove the nuts and bolts that secure the center slats to the garden bench, using a pair of vise grips and a flathead screwdriver. Hold the nuts under the slats with the vise grips and turn the bolts with the flathead screwdriver.
4
Pull off all the center slats, leaving the front and rear slats in place for the moment. Remove the slats from the back of the bench in the same manner, leaving the top and bottom slats in place.
Prepare New Slats
1
Place one of the old slats on top of one of the new slats, ensuring the two slats are even on one end. Using the old slat's mounting holes as a guide, mark the mounting hole locations on the new slat with a pencil. Trace the end of the old slat opposite the flush end onto the new slat. This is the mark for cutting the slat to size.
2
Cut the new slat to the proper length, using a coping saw. The coping saw has fine cutting teeth and is less likely to splinter the wood when cutting. Drill holes into the new slat where you made the mounting hole marks.
3
Stain the slat, and allow it to fully dry before you attach it to the bench. Make sure you stain the ends and inside the drilled holes to protect the wood as much as possible. Repeat Steps 1 through 3 of this section for all of the center slats.
Attach New Slats
1
Place the new slats onto the bench over the mounting holes. Line up the holes, and insert new bolts through the tops of the slats.
2
Thread a securing nut onto each bolt thread under the slat. Hold the nuts with a wrench or pair of vise grips, and tighten with a flathead screwdriver.
3
Remove the front and rear slats of the bench seats after the new center slats are in place. Remove the top and bottom slats off the back of the garden bench.
4
Prepare the new slats in the same manner as you did the center slats. Attach the new slats to the bench.
Tips & Warnings
Some garden benches also include a brace under the center of the seat. Some connect to the slats while others simply connect to the sides of the bench. If you have a brace connecting to slats, be sure to drill holes in the new slats to accommodate the center brace. 

Dorothy Parker --- 15 years ago -

sure...just google it~ pfft!

I want to hear from someone with first hand experience, woman! :D 

Mabs --- 15 years ago -

Google is my bff. 

Steveneedsbeer --- 15 years ago -

I have done it and it is easy if you have the correct tools an a little time. Lowes/ home depot will cut the wood for you. If you want rounded edges you can either router the edge or cheat and round it with sandpaper. Applying stain/ sealer is recommended but you really need to wait for the wood to dry out completely. Applying stain will also seal in any existing moisture causing it to rot much sooner. Good luck! You can call me if you have any questions. 

Tipsyhic --- 15 years ago -

Harbor Tool and Freight has them for cheep. Just buy a new one. 

Gigix4 --- 15 years ago -

I haven't replaced the wood on mine but I did take off all the wooden slats and refinished them - a lot of what mabs has on her comment. Then bought new stainless steel bolts and screws and put it all back together.
I can tell you that it was a project as I was only able to work on it a little at a time.
Just took my time and it came out just fine. Would I do it again ... I don't know! 

page 1
Login to add your comments!

see more discussions about...


Online now:
hit counters

Terms of Service - Privacy Policy - Ice Box

Kingwood Underground